• IV Fluid / Blood Warming System Operator’s Manual Vital Signs a GE Healthcare Company. • © 2012 General Electric Company – All rights reserved. All specifications subject to change without notice. GE, GE Monogram, and Vital Signs are trademarks of General Electric Company. ![]() * enFlow is a trademark of General Electric Company Enginivity, LLC., a subsidiary of Vital Signs, Inc. • Symbols Used on the Equipment The following symbols may be viewed on the any of the products or accessories that comprise the enFlow IV Fluid/Blood Warming System. Symbol Symbol Description Symbol Symbol Description Batch Code Catalog Number Serial Number Not made with natural rubber latex National Stock No. • System Fault XX Low Battery Lock or Password required Unlock The CE Mark is the manufacturer’s or importer’s mark of Do not throw in trash conformity declaring compliance with all applicable directives (Safety, EMC, Machinery, Medical and others). Interek is accredited by OSHA as a NRTL, as well as by the Standards Council of Canada. • CAUTIONS.... 7 UNPACKING THE ENFLOW IV FLUID/BLOOD WARMING SYSTEM.9 TO BEGIN OPERATION OF THE ENFLOW IV FLUID/BLOOD WARMING SYSTEM. Download Enflow Service Manual free. Slimm Stopwatchs Enflow Controller Model 121 Service Manual. 2006 hyundai service manual / download grd. Ge Enflow Service Manual eBooks Ge Enflow Service Manual is available on PDF, ePUB and DOC format. You can directly download and save in in to your device such as PC. Vray tree library 3ds max free download. Black areas of the bitmap are rendered as transparent portions of the object. This bitmap file must exist within the /matlibs/treemaps folder within any current Civil View resource kit. This map should always depict the same tree as the diffuse map. [Maps] Diffuse Names the bitmap that defines the color and appearance of the tree. Opacity Names the bitmap (typically black and white or grayscale) that defines the shape of the resulting tree at render time. 9 ENFLOW CONTROLLER (MODEL 120 SERIES) INDICATORS AND OPERATION. 11 ENFLOW WARMER (MODEL 100 SERIES) INDICATORS AND OPERATION. 13 CLEANING THE ENFLOW IV FLUID/BLOOD WARMING SYSTEM COMPONENTS. • IV Fluid/Blood Warming System Description The enFlow IV Fluid/Blood Warming System consists of the enFlow Warmer (Model 100 series), the enFlow Controller (Model 120 series), the enFlow Disposable Cartridge with or without IV Extension Set (Model 200 series). Within seconds, this Warming System delivers normothermic infusate to the patient at flow rates of Keep Vein Open (KVO) to 200 mL/min when input fluid temperature is 20 °C. • WARNINGS All IV fluid bags must be vented of air per IV fluid manufacturers’ directions prior to connecting to the infusion set. Ge EnflowStandard IV line protocols for priming the complete infusion set, the enFlow Disposable Cartridge, and the extension set must be followed before connecting to a patient. • Do not block the fan in the Controller as this may cause overheating. Although the Warmer has been tested to insure it will survive a drop of 1 m (3.28 ft.), care should be taken that the device is not dropped to reduce the potential of damage. • Setting the clock to the local time is optional, but usually done on initial use. No changes in performance are affected by the clock’s setting. D) Connect the enFlow IV Fluid/Blood Warmer cable to the Controller. This action is accomplished in three steps: 1. Turn right to lock. (See arrows on label.) e) The rear mounted I/0 (ON/OFF) switch on the Controller turns the power on and off. Switch the Controller to ON. Upon startup, the Controller conducts a self-test. The power indicator illuminates green, the Controller display flashes “enFlow”, a short audible “Beep”. • k) Do not wrap the Warmer in towels, sheets, blankets or drapes. Opening the Warmer covers immediately stops the heating but not the flow. M) To turn off the device, use the switch located at the rear of the controller. EnFlow Controller (Model 120 series) Indicators and Operation Keypad Controller Display. • Controller Display The Controller display continuously reflects the specific infusate temperature that the Warmer monitors and maintains. The various readouts that may be depicted on the Controller display are described in the following tabulation: Table 1: Controller Display: Normal Operating Model Activity Display Reads Display Color and. • enFlow Warmer (Model 100 series) Indicators and Operation The Warmer monitors and maintains the infusate temperature at 40 °C ± 2 °C. On the top of the Warmer, there are two status indicator lights (multicolored LEDs), which reflect the following: Power - indicates the power and operational status of the Warmer.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |